水草情迷

我照住張圖接駁，計泡器已入左2/3水，見到佢用一粒一粒水泡出，出左3粒鐘仲未見擴散杯有氣出，個擴散杯係無蛇管的，係一個膠dull，上面有一塊氣石o係面。
我想問須唔須要將水入滿擴散杯又或者要用其他秘技先可以快d出CO2呢？

I used this before too. Try adjust the output control so that it is a lot of bubble per second and you can see the pressure is high enough to push the bubble through your cup. then re-adjust the output back to 1-3 bubble per sec. 3 hours may not be enough to create the pressure, depend on how long is the plastic tube connected from output to the tank.

唔用細化器, 條喉有冇氣出呀. 有就可能係個細化未夠壓力, 等多一陣吧.
一係加快些少出氣量試下.

_________________
多多交流, 多多研究, 多多搜尋
我的水族相簿

科佬，thanks.
Today I have switched it on and got back to office and see if it work after I reach home.

好好，今晚再試下！

3粒鐘都出唔到??? 奇怪喎!
你個計泡器放係缸入面定出面?
如果係缸出面, 就要 check 清楚 計泡器 有無漏氣!
舖頭話過俾我聽計泡器較易漏氣!!

你會唔會掉轉左個止逆伐?如果係就緊係無氣出啦!

One more thing about this bubble counter - see if a black rubber ring inside the cover, and if properly fit, otherwise, when you overtighted the cover, it will 'slip' and thus leak. Use some water pipe "bandage" (the white one you use to fix the water pipe) to help to get tighter cover (but not over screw - it is easy to break and leak). This bubble counter is NOT good and should avoid to buy the same one if broken.
To fill the diffuser with water (if you do need to do this) - try to use a dripper (like the one to test PH) and cut a short gas pipe (say 3 - 5 cm) connect it to the dripper - then suck some water in - connect the other end of the gas pipe to the diffuser - pump the sucked water into it, try it several time, you may put the diffuser upside down to try the best angle for the pumped water to be kept in the diffuser. This can also be used to "suck" the dirt out from the diffuser (e.g. the fluid due to DIY CO2 overflow) Hope this help. Sorry cannot type Chinese in office

你只須要檢查有無其他地方漏氣, 同埋止逆閥有無倒轉裝, 如果都無問題, 咁就扭開個擴散杯蓋同拎開塊擴散片, 放入缸咁d水就入滿擴散杯, 係水入面裝翻好個擴散杯再試0下啦! (或者將塊擴散片先浸一陣熱水先再裝翻,效果會好d)

我都用緊巴比倫CO2個擴散杯,無問題啊!

巴比倫個計泡器同擴散杯實在唔夠 Smart~
我零願唔計泡 同埋 改用 Boy-U擴散杯!
不過巴比倫個錶頭好靚~

如果熄左，要唔要等好耐先再出架？